| Testing and Measuring Products |
 |
 |
 |
|
A broad range of Testing & Measuring Products are offered for insulation testing, measuring Earth resistance , Primary and Secondary current injection, Oil BDV Testing, Moisture in Oil Measurements, Specific gravity, voltage, current, power, harmonics and vibrations.
Insulation Tester 500V
It’s analogue hand cranked operated economical insulation tester.And drive insulation tester is used for measuring insulation resistances of various electrical machineries, control panels, switching equipment, insulators cables, wiring and various other devices ranging from small electrical units to large size transformers.
Click here for Catalog
Insulation Tester 1KV
It is a Insulation resistance measurement tester with 10V Step Automatic measurement in sockets with the UNI-Schuko adapter with possibility of configuring pairs of measured cables, Continuous indication of insulation resistance or leakage current, Automatic discharge of capacitance of tested object after the insulation resistance measurement.
Click here for Catalog
Insulation Tester 2.5 KV
Insulation resistance measurement haning Selectable measurement voltage 100, 250, 500, 1000 V or any in the range of 50…2500 V at 10 V resolution, Continuous indication of measured insulation resistance or leakage current, Automatic discharge of measured object capacitive voltage after the completion of insulation resistance measurement, Acoustic signaling of 5 seconds intervals to facilitate capturing time characteristics, Metered T , T and T test times for measuring one or two absorption coefficients from the range of 1…600 s, 1 2 3 Capability of automatic measurement of multiwire cables with the additional AutoISO-2500 adapter.
Click here for Catalog
Insulation Tester 5 KV
Insulation resistance measurement provides Test voltage selection between 250...5000V in 50V intervals, or predefined 250, 500, 1000, 2500, 5000V. On-line insulation resistance measurement or leakage current. Automatic discharge of tested object’s capacitance after measurement of insulation resistance. Direct measurement of one or two absorption coefficients. Acoustic determination of 5 seconds time intervals that facilitates to take time characteristics during insulation resistance measurement.
Click here for Catalog
Insulation Tester 10 KV
Is a TeraOhm 10 kV is a professional high voltage insulation tester with added diagnostics tools. It is specially well suited for: Power transformers .Measuring transducers in distribution networks .Testing insulation resistance of rotating machinery and cables .Production line periodic testing and maintenance Troubleshooting and analysis of all kinds of insulation problems Because of its robustness (CAT IV protection) it is best suited for industrial environment. Provided Insulation resistance up to 10 TO · Diagnostics tools (PI, DAR, DD) · Step voltage insulation test • Test voltage 500 V - 10 kV DC, adjustable in 25 V steps • MAX charging current 5 mA • Automatic discharge of capacitive loads · Digital and bar graph results with date and time • Optional Windows compatible PC software TeraLink · RS232 and USB isolated communication ports.
Click here for Catalog
Insulation Tester 12 KV
It is a Robust design for field use with weatherproof protection to IP64 (with lid closed). Having Internal Memory MAX 40,000data with Built-in Print Screen Function enables to record display screen (Records 32 screens MAX) Downloading to PC- Using the USB cord and the PC software included as standard accessory, the memory data or the measuring data can be transmitted to a PC at real time. Mains and battery powered Internal rechargeable battery can be charged during normal operation. Auto-discharge function and voltage output warning function. Large Backlit LCD Graphic display with bar graph.
Click here for Catalog
Earth Testers
It is a earth resistance tester allows taking measurement of earthing resistance using auxiliary electrodes, earthing resistance using auxiliary electrodes and clamp (for measurements of multiple earthing).earthing resistance using double clamps (for measurement of earthing when it is impossible to use auxiliary electrodes), ground Resistivity (Wenner method) .measurement of continuity of equipotent bondings and protective conductors (meeting the requirements of IEC 60364-6-61:2000 section 6.12.2) with auto-zero function – with current 200mA.
Click here for Catalog
DC Earth Fault Tester
Multi-feeder DC distribution systems utilize ungrounded 12 VDC to 250 VDC battery assemblies for control, instrumentation and plant _ equipment operations. DC ground faults in one polarity of a multi-feeder system will diminish the reliability of the system if they remain uncorrected. The DC ground fault analyzer GFAL-A is utilized in situations where a high degree of service reliability and safety from the multi-feeder. DC distribution system is required and desirable in All type of Generating Power Plants & Distribution Substations. Help to calculate the fault resistance in each polarity with respect to ground Analyze and functional test the DC alarm system operations. Detect spikes and AC power contamination in battery distribution. GFAL-B (receiver) are battery operated portable instruments that utilizes a DC tracking signal create by the interrupter and the fault resistance. A Hall Effect magnetic Sensor Assembly is attach to the GFAL-B that wrap around the conductors to track the tracking signal. The hand held unit GFAL-B houses the microprocessor and the analog electronics and track the tracking signal. It is designed to analyze and locate DC ground faults on ungrounded DC battery multi-feeder distribution systems. The design is very successful, and today we have is an instrument capable of quickly locating these DC ground faults.GFAL-B (receiver) are battery operated portable instruments that utilizes a DC tracking signal create by the interrupter and the fault resistance. A Hall Effect magnetic Sensor Assembly is attach to the GFAL-B that wrap around the conductors to track the tracking signal. The hand held unit GFAL-B houses the microprocessor and the analog electronics and track the tracking signal. It is designed to analyze and locate DC ground faults on ungrounded DC battery multi-feeder distribution systems. The design is very successful, and today we have is an instrument capable of quickly locating these DC ground faults.
Click here for Catalog
AC/ DC Clamp Meter
Is a safe, Insulated measuring Clamp with double moulded housing , auto ranging,/ manual , range selection meter. Provided DC current measurement (CMP-401 only) and AC current and 2AC/DC voltage measurement up to 600V. With Resistance measurement and continuity test with acoustic signalling (beeper) for resistance below 50. And Temperature measurement (Fahrenheit and Celsius units).
Click here for Catalog
Leakage Current Metrer
Is a digital clamp meter has been designed forclamp measurements of AC leakage current. Provides AC current measurement up to 200A with high resolution (0,1mA) in three measuring ranges: 200mA, 2A, 200A. Is has display LCD 3 digits (max 1999), with white LED backlight having internal diameter clamp approx. 30mm (1,2),DATA HOLD function, for holding measured values.
Click here for Catalog
Digital Multimeter
This Multimeter has been designed for the purpose of measurements of AC/DC voltage, AC/DC current, resistance, capacitance, frequency, duty cycle, temperature and also for testing diodes and continuity. The most important features of CMM-10 Autoranging/manual range selection with DATA HOLD” function, for holding measured values. REL” function, which allows you to make measurements relative to a stored reference value. With Continuity test with acoustic signalling (beeper) and AUTO-OFF” function.
Click here for Catalog
CT/PT Tester
This new method allowed utilities around the world to test their CT’s in an easier and faster way than using traditional methods without jeopardizing accuracy. Following feedback from our users, our Model 590G-V2 CT is the latest version of this successful and well proven CT error tester. This new version includes all the advantages of the previous version with additional testing features, better accuracy and a smaller size and weight.This CT tester not only lowers testing costs by being simple, fool-proof and fast. It also allows utilities to pursue the very important (yet many times forgotten) task of testing installed CT’s for detecting tampering, and minimizing losses due to faulty CT’s.
Click here for Catalog
Power Quality Analyzer
Power Harmonics Analyser is a complete 3phase, portable power analyser for use in industry, utilities and for general power quality diagnostics purposes. Provides High accuracy measurement and recording of power quality parameters (U,I,f, cos ?, PF, P,Q,S, current and voltage harmonics up to 63 rd order, etc.). Having MS Windows compatible PC SW Power Link serves for downloading, management of recorded data and preparation of test reports.
Click here for Catalog
High Voltage Detector
Is Self-Testing Voltage Detectors are used to verify live or de-energized conductors. These testers may be used with rubber insulating gloves or hot sticks using the splined universal end fitting. Testers indicate the presence of voltage with an extra bright LED light and a distinctive audible signal. It is recommended that the tester be moved closer to the conductor until a warning is indicated, or it touches the conductor, apparatus, or elbow test point. Each tester requires three “C” batteries (included). Salisbury’s Self-Testing Voltage Detectors allow testing to be continuous and automatic. An intermittent flash and beep confirms the detector is functioning properly.
Click here for Catalog
Microprocessor Based Oil BDV Test Set
Is a fully automatic tester for determination of the dielectric breakdown voltage of insulating liquid. It has benn designed for laboratory use as wellas for field use for service a nd commissioning. Its is very comfortable. And easy in use. The requested testing standard may be selected via menu. The corresponding electrode type as well as the electrode type as the electrode spacing will be displayed for confirmation before starting the test. It is fully automatic tester for laboratory and field use during service and commissioning testing voltage upto 100 KV . Pre programmed for common national and international testing standards uoto ten free programmable user testing standards.
Click here for Catalog
Auto Transformer (VARIAC) 1
Is partially or fully moulded in reinforced polyester Resin. Its coils made from high grade CRGO silicon steel 99.9 percent pure copper. The output voltage variation is smooth, continuous, beakless & linearly proportional to angular rotation. It works with high efficiency and with negligible waveform & power factor distortion. The operating voltage for single phase is 240V AC, 50-60 Hz, 1 Ohm.
Click here for Catalog
Auto Transformer (VARIAC) 3
Is partially or fully moulded in reinforced polyester Resin. Its coils made from high grade CRGO silicon steel 99.9 percent pure copper. The output voltage variation is smooth, continuous, beakless & linearly proportional to angular rotation. It works with high efficiency and with negligible waveform & power factor distortion. The operating voltage for single phase is 415 V AC, 50-60 Hz, 3 Ohm 4 wire.
Click here for Catalog
AC Hipot Test Set
AC Hipot Tester are designed & used for testing Cables & Electrical equipments as per IS standards.We offer wide range of HV AC test sets up to 300KV with multiple KVA ratings specially designed to perform quick and accurate AC dielectric tests.The HVT series assures accurate voltage measurements using an internal high voltage divider, rather than less accurate primary metering. The HVT series also features a triple range current meter in the return leg of the high voltage transformer for accurate current measurements. A guard circuit prevents stray or surface leakage from being measured by the current meter. To ensure safe operation the unit is equipped with a fast acting circuit breaker, zero start interlock and provision for an external interlock.
Click here for Catalog
DC Hipot Test Set
Is a portable testers have been designed to be used in testing high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for surge arresters, cable breakdown testing, capacitor charging and other laboratory use. Contains all features needed for electrical maintenance, testing of new or installed electrical apparatus like cables, zinc oxide arrester, motor etc. arrester, motor etc. It provides Bring great convenience to measurement of zinc oxide arrester with the added function of high accuracy 75%VDC-1mA.
Click here for Catalog
Model # APTS 3 - DC Hipot Tester
The APTS three-phase protection relay test set is the flagship multipurpose relay test set manufactured by RES. The APTS utilises the latest digital signal processing based waveform synthesis techniques coupled with advanced low-noise switching amplifier technology. This combination enables the APTS to deliver precision waveforms at the highest output power available in a portable lightweight computerised test set anywhere. The highest burden single & three-phase electromechanical relays as well as the latest microprocessor based relays can be tested directly and without the need for additional accessories or amplifiers. The APTS has six, very high power, DC coupled sources/amplifiers. These are tightly regulated and continuously monitored, maintaining accurate, low distortion, voltage and current levels independently of the supply input or load. If any APTS output deviates from its programmed setting for any reason (open/short circuit, overburden, etc.) then the operator is warned via a message on the PC & test set front panel.The APTS has six, very high power, DC coupled sources/amplifiers. These are tightly regulated and continuously monitored, maintaining accurate, low distortion, voltage and current levels independently of the supply input or load. If any APTS output deviates from its programmed setting for any reason (open/short circuit, overburden, etc.) then the operator is warned via a message on the PC & test set front panel.
Click here for Catalog
Phase Angle Meter
This meter is an accurate general purpose instrument deisgned to suit the needs of electricity supply authorities. It has all the features of more expensive imported units plus extra features such as switch selectable +/- 180 degree C OR 360 degree C readout and analogue output.
Click here for Catalog
Vaccum Bottle Tester
The VBT-60 is a microprocessor-based, portable 60 kV dc vacuum bottle tester. This lightweight, portable tester is designed for testing circuit-breaker vacuum bottles in the field and at the shop. Test voltages can be selected from 10 kV dc to 60 Kv dc in 5 Kv steps. The high-voltage test time can be set from 5 seconds to 2 minutes. The test voltage is raised to the selected voltage and held for the test time duration. After the test time duration has elapsed, the test voltage is returned to zero. If a flash-over condition occurs, such as bottle failure, the test voltage is immediately turned off, a “Failure” message is displayed on the LCD screen, and the “TEST FAIL” LED light on the unit is also illuminated. The presence of high voltage is indicated by an audible tone and an illuminated “HIGH VOLTAGE” LED light. For additional operator safety, an “ARM” switch must be held down during testing. The VBT-60 features a back-lit LCD screen (16 characters by 2 lines) that is viewable in both bright sunlight and low-light levels. A turn-and- press knob is used to control the unit. An RS-232C interface port is provided for factory calibration and diagnostic testing. The VBT-60 is furnished with a 10-foot test cable that is terminated with a quick-disconnect test clip.
Click here for Catalog
Thermal Image Camera
It is a compact sized; lightweight -13 oz camera with thermal sensitivity < 0.1 degree C @ 25 degree C . It is easy to use focus free lens camera stores upto 500 JPEG Images. Having color display of 2.8 “LCD. It can be used in Motor - Internal Winding Problem Electrical - Hot Fuses etc.
Click here for Catalog
Phase Sequence Meter
It checks Phase sequence and phase status. It has Graphical multiline LCD indicates phase orientation (clockwise or counter-clockwise) and whether each of the three phases is live. No battery required. Easy to read graphical multilined LCD displaying phase orientation and showing which three phases is live.
Click here for Catalog
Micro Ohmmeter 10 A
The MMR Series meters are professional portable instruments for measuring very low resistances. Due to their special measurement algorithm they can be used for both resistive and inductive type of a specimen that makes MMR series perfect instruments for electricians testing electrical junctions, motors and power transformers windings. The results can be stored in the internal memory and send to a computer via serial interface. A quick PASS/FAIL test function with results displayed and acoustically indicated simplifies measurements considerably. MMR-630 is designated not to be effected by interference up to 20mV and to show noises from 20 to 100mV (so in edge conditions even 5 times higher than measured drop of potential). Memory store for up to 990 results and a communications facility for transferring data from the device to a PC.
Click here for Catalog
Vibration Meter
Is a heavy duty vibration meter with mounted pick. With Built-in RS-232 PC serial interface with optional Data Acquisition software. Velocity range of 7.87in/s or 200mm/s; Acceleration range of 656ft/s2 or 200m/s2.Record mode stores the maximum and minimum values for later recall. Its application are found in Motor bearings, Pumps, fans, rotating machinery etc.
Click here for Catalog
Tachometer
Is a Instrument to measure speed having large 5 digit LCD Display with built in memory which recalls last max/ min value stored. Provides auto ranging with 0.05% accuracy.
Click here for Catalog
Lux Meter
Is Light meter which Measures light intensity up to 20,000 Foot-candles or 200,000 Lux With high resolution to 0.01 Fc/Lux . Ideal for measuring parking lot illumination, security lighting, and night ATM areas. Provides Cosine and color corrected measurements with High accuracy of ± (5% reading + 0.5%FS).
Click here for Catalog
Thermo Hygrometer
Is a Easy View Hygro-Thermometer. It’s Compact and rugged design features to large display and bargraph. It Display any two parameters (Temperature and Humidity or Dew Point, or Wet Bulb) simultaneously. Its Timer function displays the elapsed time (mins : secs and day : hour) to the minimum and maximum readings. Its applications are found in Monitor Relative Humidity and Temperature in factories, clean rooms, offices, and greenhouses and Produce reports of overnight or long term humidity and temperature fluctuations.
Click here for Catalog
Hydrogen Leak detector
Is a handheld Hydrogen Leak Detector is the industry’s most versatile portable hydrogen leak detector able to respond to the widest range of hydrogen gas concentrations without the need of any peripheral equipment. The sensor probe has unique visual LED array that will effectively help to navigate to the source of a hydrogen leak when hydrogen gas is produced, used, transported or stored. With two sensing elements on the same semiconductor die, it can detect hydrogen leaks as low as 15 ppm and will not saturate or be destroyed when destroying high concentrations of hydrogen upto 100%. The flexible cable allows the sensor probe access to virtually all potential leak sources.
Click here for Catalog
Sound Level Meter
It is digital Sound Level Meter providing ±2dB accuracy with 0.1dB resolution. Its application are found in monitoring workplace machinery, Installing audio and alarm systems, product noise and certification and reductions.
|
You are here :
Home 
Utility Products T & M Products
Utility Products T & M Products
Currency Convertor
 | The World's Favorite Currency Site |
Engineering Units converter
Click Here to Download the Application. Download Adobe Reader
 | Click Here to Download the Adobe Reader. |
New Delhi Weather
